Small. Fast. Reliable.
Choose any three.

# SQL As Understood By SQLite

[Top]

## VACUUM

vacuum-stmt:

The VACUUM command rebuilds the database file, repacking it into a minimal amount of disk space. There are several reasons an application might do this:

- Unless SQLite is running in "auto_vacuum=FULL" mode, when a large amount of data is deleted from the database file it leaves behind empty space, or "free" database pages. This means the database file might be larger than strictly necessary. Running VACUUM to rebuild the database reclaims this space and reduces the size of the database file.

- Frequent inserts, updates, and deletes can cause the database file to become fragmented - where data for a single table or index is scattered around the database file. Running VACUUM ensures that each table and index is largely stored contiguously within the database file. In some cases, VACUUM may also reduce the number of partially filled pages in the database, reducing the size of the database file further.

- When content is deleted from an SQLite database, the content is not usually erased but rather the space used to hold the content is marked as being available for reuse. This can allow deleted content to be recovered by a hacker or by forensic analysis. Running VACUUM will clean the database of all traces of deleted content, thus preventing an adversary from recovering deleted content. Using VACUUM in this way is an alternative to setting PRAGMA secure_delete=ON.

- Normally, the database page_size and whether or not the database supports auto_vacuum must be configured before the database file is actually created. However, when not in write-ahead log mode, the page_size and/or auto_vacuum properties of an existing database may be changed by using the page_size and/or pragma auto_vacuum pragmas and then immediately VACUUMing the database. When in write-ahead log mode, only the auto_vacuum support property can be changed using VACUUM.

By default, VACUUM only works only on the main database. Attached databases can be vacuumed by appending the appropriate schema-name to the VACUUM statement.

Compatibility Warning: The ability to vacuum attached databases was added in version 3.15.0 (2016-10-14). Prior to that, a schema-name added to the VACUUM statement would be silently ignored and the "main" schema would be vacuumed.

### VACUUM with an INTO clause

If the INTO clause is included, then the original database file is unchanged and a new database is created in the filename given by the argument to the INTO clause. The new database will contain the same logical content as the original database, fully vacuumed.

The VACUUM command with an INTO clause is an alternative to the backup API for generating backup copies of a live database. The advantage of using VACUUM INTO is that the resulting backup database is minimal in size and hence the amount of filesystem I/O may be reduced. Also, all deleted content is purged from the backup, leaving behind no forensic traces. On the other hand, the backup API uses fewer CPU cycles and can be executed incrementally.

The filename in the INTO clause can be an arbitrary SQL expression that evaluates to a string. The file named by the INTO clause must not previously exist, or else it must be an empty file, or the VACUUM INTO command will fail with an error.

The argument to INTO can a URI filename if URI filenames are enabled. URL filenames are enabled if any of the following are true:

- The SQLite library was compiled with -DSQLITE_USE_URI=1.
- The sqlite3_config(SQLITE_CONFIG_URI,1) interfaces was invoked at start-time.
- The database connection that is running the VACUUM INTO statement was originally opened using the SQLITE_OPEN_URI flag.

The VACUUM INTO command is transactional in the sense that the generated output database is a consistent snapshot of the original database. However, if the VACUUM INTO command is interrupted by a unplanned shutdown or power lose, then the generated output database might be incomplete and corrupt. Also, SQLite does not invoke fsync() or FlushFileBuffers() on the generated database to ensure that it has reached non-volatile storage before completing.

### How VACUUM works

The VACUUM command works by copying the contents of the database into a temporary database file and then overwriting the original with the contents of the temporary file. When overwriting the original, a rollback journal or write-ahead log WAL file is used just as it would be for any other database transaction. This means that when VACUUMing a database, as much as twice the size of the original database file is required in free disk space.

The VACUUM INTO command works the same way except that it uses the file named on the INTO clause in place of the temporary database and omits the step of copying the vacuumed database back over top of the original database.

The VACUUM command may change the ROWIDs of entries in any tables that do not have an explicit INTEGER PRIMARY KEY.

A VACUUM will fail if there is an open transaction, or if there are one or more active SQL statements when it is run.

An alternative to using the VACUUM command to reclaim space after data has been deleted is auto-vacuum mode, enabled using the auto_vacuum pragma. When auto_vacuum is enabled for a database free pages may be reclaimed after deleting data, causing the file to shrink, without rebuilding the entire database using VACUUM. However, using auto_vacuum can lead to extra database file fragmentation. And auto_vacuum does not compact partially filled pages of the database as VACUUM does.